Poseidon 2250 je merilna naprava na katero lahko priklopimo do 26 senzorjev ki omogoča pošiljanje e-pošte v primeru preseženih vrednosti. Vrednosti in konfiguracija so na voljo prek spletnega vmesnika, ternutne vrednosti pa je možnost prenesti (WEB, XML, e-naslov, CSV). Model 2250 deluje tudi kot datalogger z vgrajenim Flash pomnilnikom. Tako omogoča delovanje, beleženje in kasnejše pošiljanje izmerkov tudi ko internetna povezava ni na voljo.

Do 26 senzorjev(RS485), dolžine do  1000 m.
3 Digitalni vhodi za relejna stikala.
Priklop na GSM modem za direktno pošiljanje SMS-ov.

OSNOVNE ZNAČILNOSTI

Senzorji so povezani preko 1-Wire (RJ11), skupne dolžine napeljave do 1000 metrov. Vsak senzor spremlja določene vrednosti in v primeru preseženih vrednosti ali vklopa/izkola kontakta o tem pošlje obvestilo prek e-pošte ali SNMP trap.

Sonde na voljo

Model Poseidon 2250 podpira do 26 senzorjev (sonde), za temperature, vlage, pretoka zraka in drugih vrednosti spremljanja.
Temperatura (do 26 senzorjev do 1000 metrov, -55 ° C do 640 ° C)
Vlaga (do 25 senzorjev do 1000 metrov)
Binarni input / kontaktna (do 3 detektorji dima, gibanja, poplave, kot, odpriranje/zapiranje vrat, pretoka zraka itd)
General input (0 do 10V, 4 do 20mA - z uporabo zunanjih pretvorniki za RS-485)
Temp-1Wire
Temp-485
Temp-485-Pt100
HTemp-485
Humid-1Wire
Sens-UI
Detektor poplave
Detektor uhajanja plina
Javljalnik dima
Detektor gibanja

Ethernet port 

+ Interface RJ45 (10BASE-T) – 10 Mbit or 10/100 Mbit network compatible+ Supported protocolsIP: ARP, TCP/IP (HTTP, Modbus over TCP), UDP/IP (SNMP)+ SNMP compatibilityVer:1.00 compatible, some parts of the ver 2.0 implemented Port 1 - RS-485+ Connector RJ45 (8 pins)+ Sensors / distance Max. 31 sensors, up to 1 000 metres+ 1-Wire interface Data, GND, +5V   (max. 10 sensors, up to 15 metres) Port 2 - 1-Wire + Connector RJ12 (6 pins - 4 pins used only)+ Sensors / distance Max. 10 sensors, up to 20 metres Port 3 - RS-232 + Connector Cannon 9 male (DB9M)+ PinoutStandard IBM PC (RxD,TxD,RTS,CTS, DTR, DSR, GND)+ Usage Serial Setup, Output pins, GSM modem interface+ Sensors / distance No sensors, up to 20 metres+ OUTPUTS 2 additional outputs (1/0), RTS(+10V/-10V), DTR(+10V/0V) Digital digital inputs + 3x Contact inputs (Dry contact)Galvanic isolated up to 50V DC, max distance 30m,
connect it with a contact directly (dry contact). LED Status indicators+ POWERGreen - power OK+ LINK & ActivityGreen - Ethernet connectivity+ SENSOR RS-485Yellow slow blinking - Any RS-485 sensor not found
Yellow fast blinking - RS-485 sensors reading, value valid+ MODE & RS-232 Red - blinking - Device is in the RS-232 Setup mode
Red - lit - One (or more) of the sensors is out of the Safe Ranfe
Green slow blinking - RS-232 sensor not found
Green fast blinking - RS-232 sensor reading, value valid DIP SWITCH configuration+ DIP1   - RS--232 Setup modeON   = RS-232 Setup mode
OFF = Run mode+ DIP2Not used+ DIP3   - SecurityON   = Security mode - remote configuration disabled
OFF = Non-Security mode - remote configuration enabled+ DIP4Not used Physical parameters + Voltage requirements12V / 250 mA DC - coaxial power connector (barrel), GND on the shield+ Dimensions 25 x 82 x 90 [mm] (H x W x D )+ Weight 450 g Functional parameters Device SETUP configuration possibilities - RS-232 Setup - over any RS-232 terminal 9600 8N1
- UDP Config - IP address assign via UDP with using PN Eye
- TCP Setup - Terminal configuration and sensors management
- WWW Setup - HTTP Flash application
- SNMP (just for some parameters)